Hot Sale Curtis Drive Motor Controller 1228-2901 24V-110A for Golf Carts

• After-sales Service: Yes
• Warranty: 1 Year
• Motor Type: DC Motor
• Shipping Cost: Estimated freight per unit.: about shipping cost and estimated delivery time.
• Currency: US$
• Return&refunds: You can apply for a refund up to 30 days after receipt of the products.
• Model NO.: 1228-2901
• Voltage: 24V
• Current: 110A
• Operating Ambient Temperature: -25°c to 50°c
• Dimensions: W91XL156xh43 mm
• Application: Electric Vehicles
• Package Environmental Rating: IP40
• Quality: Excellent
• Transport Package: Carton/Pallet
• Trademark: Curtis
• Origin: China(Mainland)
• Production Capacity: 3000 Pieces/Month
• Package Size: 15.00cm * 10.00cm * 5.00cm
• Package Gross Weight: 0.700kg

Product Description

  Hot Sale Curtis Remote Programmable Permanent Magnet Drive Motor Controller 1228-2901 24V-110A for Golf Carts

Product Description 

Specifications:

• PWM operating frequency: 15 kHz
• Electrical isolation to heatsink (min.): 500 VAC
• Dielectric resistance: >1 MΩ (DC test)
• Heatsink overtemperature: linear cutback starts at 92°C; complete cutoff at 134°C
• Heatsink undertemperature: 50% armature current at -25°
• Undervoltage cutoff: 14 V
• Overvoltage cutoff: 34 V

The CURTIS 1228 MultiMode™ controller is a permanent magnet motor speed controller designed for use in mobility aid scooters and other small electric vehicles, such as sweeper/scrubbers.

Overview:

       The 1228-2901 offers smooth, silent, cost effective control of motor speed and torque. A four quadrant, full bridge power output stage provides for solid state motor reversing and full braking power without additional relays or contactors.
       The 1228-2901 controller is fully programmable, via the CURTIS Model 1313-4401 Handheld Programmer or 1314 PC Programming Station. This means the controllers can be tailored to the needs of specific applications. In addition to configuration flexibility, use of the programmer offers diagnostic and test capability.
 

Key Features:

• CURTIS Model: 1228-2901
• Norminal Battery Voltage (Volts): 24V
• 15 Second Current Rating (amps): 110
• 1 Minute Current Rating (amps): 110
• 1 Hour Current Rating (amps): 40
• Peak Boost Current (amps): 90
• Max Boost Current Duration: 10 Second
• Minimum motor resistance: 130 mΩ
• B+, B- logic pin current (max.): 9 A (pins 1, 2 and 10, 11 on 18-pin connector)
• KSI input current (typical): 50 mA without programmer; 150 mA with programmer
• KSI input current (peak): 1.5 A
• Logic input current (typical): 1 mA at 24 V
• Horn output current (max.): 15 mA
• BDI output voltage and current (max.): 0-5 V, 2 mA
• LED output current (max.): 15 mA
• Electromagnetic brake coil resistance (min.): 32-200 Ω
• Throttle Type: By default, the Throttle Type of controller 1228-2901 is set as Type "0". The controller 1228-2901 can be programmed to accept single-ended, wigwag, or inverted wigwag signals from a 5kΩ, 3-wire pot or from a 5V throttle. The throttle input signal type options (Types "0" through "5" in the Throttle Type programming menu) are listed as below:
  • 0 = wigwag pot or voltage throttle
  • 1 = inverted wigwag pot or voltage throttle
  • 2 = single-ended pot; maximum speed = 5kΩ
  • 3 = inverted single-ended pot; maximum speed = 0
  • 4 = single-ended voltage throttle; maximum speed = 5V
  • 5 = inverted single-ended voltage throttle; maximum speed = 0
• Dimensions: W91xL156xH43 mm
• Net Weight: 0.6 kg
• Regulatory compliance: Designed to ANSI RESNA WC 14/21, ISO 7176-14, ISO 7176-21, and EN 12184. Documentation available to support 510K FDA filings.
• Operating ambient temperature range: -25°C to 50°C
• Storage ambient temperature range: -40°C to 70°C
• Package environmental rating: IP40

Features Include:

• Full bridge power MOSFET design, providing
  • infinitely variable forward, reverse, drive, and brake control
  • silent high frequency operation
  • high efficiency
• Complete diagnostics through the CURTIS programmer and a status LED
• Full compliance with all applicable international standards
• Available for single-ended or wigwag 5kΩ potentiometer throttles and 5V throttles (both standard full stroke and restricted range)
• MultiMode™ input selects between two different operating modes, thus allowing optimization of vehicle characteristics for different driving conditions (for example, indoor/outdoor)
• Speed limit input provides linear variable speed limiting when an external speed limit pot is used
• Current limiting in both driving and regenerative braking modes
• Load compensation stabilizes speed on ramps and over obstacles
• Speed scaler eliminates variations in maximum speed that would otherwise result from variations in battery charge levels
• High pedal disable (HPD) function with lockout monitors status of the throttle during turn-on and prevents operation until the throttle has been returned to neutral
• Key-off deceleration function provides a controlled deceleration if the keyswitch is turned off while driving
• "E Stop" provides a faster deceleration for emergency stops
• Seat lift function simplifies the wiring required to implement seat lift in DME scooter applications
• Comprehensive fault detection monitors main contactor, output stage, throttle demand vs. output, etc., and disables the drive functions if any conditions are outside specified limits
• ISO 7176 compliant throttle fault detection circuitry inhibits driving if throttle pot signal goes out of range for any reason
• Missing/shorted brake detection forces neutral in the event of an open or shorted brake circuit
• Anti-rollback/anti-roll-forward function sets brake delay according to speed and direction for improved braking response and minimized rollback on hills, etc.
• Reverse beeper option can be used to drive a low current dc horn when vehicle is in reverse
• "Push" input electrically releases brake for key-on pushing (requires that the vehicle be stopped first)
• "Push-Too-Fast" feature guards against unpowered vehicle runaway by powering up and regulating motor voltage to limit vehicle speed
• Inhibit input disables the controller and puts the vehicle in a safe state during charging, etc.
• Power saver deactivates the main relay after 25 seconds of nonoperation and deactivates the entire controller after the programmed sleep delay has elapsed
• BDI output can be used to provide data to a voltmeter; the BDI output can be "stuffed" (optional) in order to display the battery state of charge during battery charging even while the keyswitch is turned off
• Undervoltage cutback function protects against operation at low battery voltage
• Overvoltage protection shorts the motor and disables driving in the event of excessive battery voltage
• Thermally protected
• Reverse polarity protected (battery input)
• Easily programmable through the CURTIS Model 1313-4401 Handheld Programmer or 1314 PC Programming Station.

Our Company

 Hefei Huanxin Technology Development  Co., Ltd. has been devoting ourselves to developing and manufacturing and other since 2004. We are located in Hefei, Anhui Province, with convenient transportation access. We employ over 101 - 200 People staff members. We have achieved great improvement since our company was founded in 2004. We abide by the motto of First-class quality,Reasonable price, Best service and Professional product support. 

 

On Exhibition



Certificates

FAQ

Q1. Can I have a sample order?
A: Yes, we welcome sample order to test and check quality.

Q2. What about the lead time?
A: Samples arrived often need 3-5 days.

Q3. Do you have any MOQ (minimum order quality)limit?
A: Low MOQ, 1pc for sample checking is available.

Q4. How do you ship the goods and how long does it take to arrive?
A: We often ship by DHL, UPS, FedEx or TNT. It usually takes 3-5 days to arrive. Airline and sea shipping is also optional.

Q5. How to proceed an order?
A: Initially, let us know your requirements or application. Besides, We quote according to your requirements or our suggestions. Thirdly, customers confirms the samples and places deposit for formal order. Finally, We arrange the production.

Q6. Is it acceptable to print my logo on the product?
A: Yes. Please inform us formally before our product and confirm the design firstly based on our sample.

Q7: Do you offer guarantee for the products?
A: Yes, we offer one-year warranty for our products.

Q8: How to deal with the flaw?
A: Our products are produced in strict quality control system and the percent of pass is often maintained over 99.8%.

Package and Shipping 

Package:Normally we use the standard exporting parcel. We also can package the item according to clients' request .

Shipping : 

1. By Couriers: DHL, UPS, FEDEX, TNT are the main courier companies we are cooperating.

2. By Air: Delivery from the Shanghai airport to customer's destination city air port.

3. By Sea: Delivery from the Shanghai/Guangzhou/Ningbo sea port .